ECLIPSE STAINLESS STEEL BLENDER
complies with
INTERNATIONAL
Model:
6 2 0 0 2
IEC60335
SAFETY SPECIFICATIONS
5 0 0 W
PLEASE READ ALL INSTRUCTIONS BEFORE USE
2 y e a r g u a r a n t e e
MW_62002_Eclipse_IM.indd
1
24/06/2011 15:30:58
the plug from the power supply outlet, or to
insert or remove the glass jar and/or lid.
12. This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
(The switch does not permanently engage in the
‘PULSE’ function. You have to hold the switch in
the ‘PULSE’ (“M” position) or turn it repeatedly to
the “M” position.)
WARNING: DO NOT LEAVE THE APPLIANCE
UNATTENDED WHILE IN OPERATION.
instruction concerning use of the appliance by
a person responsible for their safety.
After using the blender, always turn the switch
to the “0” position and remove the plug for the
power supply outlet.
Before first use
All parts of the blender must be thoroughly
cleaned before being used for the first time.
To remove the glass jar simply remove it from the
motor base. There is no need to rotate the glass
jar to remove it.
Assembling the Jar:
1. Put the rubber sealing ring (5) on the inner
edge of the blade unit (6).
2. Put the blade unit with sealing ring into the cup
base (7).
3. Inset the ring (4) on the bottom of jar first, then
Insert the assembled cup base onto the bottom
of the jar (3) and turn clockwise to secure
firmly in place.
4. Secure the Measuring Cap (1) onto the Lid (2).
5. Secure the Lid onto the Glass Jar and push
down lid to clip into place.
Useful tips:
• To achieve the best results when processing
solid ingredients, place small portions of the
specific food content into the glass jar piece
by piece, instead of placing a large quantity all
at once.
• If you are processing solid ingredients, cut
them into small pieces (2-3cm) first.
• When mixing/blending solid ingredients start
off first with a small amount of food content.
Gradually add more and more food content
through the opening in the lid.
Inserting the Jar:
• Always place your hand on top of the
blender when you are operating the appliance.
• For stirring solid or very thick liquid
ingredients use the blender in “PULSE” mode
(“M” position) to prevent the
1. Ensure that the blender is switched off
(Switch must be in the “0” position).
2. Place the jar assembly (9) on to the motor
base (8) and press down until securely
engaged.
blades becoming clogged.
Instructions for Use
Motor Base:
1. Insert the food contents you wish to process
into the jar.
Never immerse the motor base in water. Wipe it
only with a soft, clean damp cloth. For simple
cleaning/ rinsing of the assembled glass jar:
2. Place the lid on the jar and close securely.
Place the measuring cap into the hole in the
lid and turn clockwise to lock in place.
3. Place your free hand firmly on the lid and
apply a downward force before switching on
the appliance. The appliance is fitted with a
safety switch and requires the jar to be secured
to the motor base in order for the appliance to
operate.
Empty the glass jar and fill it with clean water.
Place the glass jar on the motor base and turn the
switch several times to the “M” position. Empty
the glass jar and rinse until clean.
WARNING: THE JAR OR ANY PART OF THE
JAR ASSEMBLY IS NOT TO BE CLEANED
USING A DISH WASHER. USE OF A DISH
WASHER MAY RESULT IN DAMAGE OF THE
APPLIANCE AND THE WARRANTY WILL BE
VOID.
4. Set the switch to desired/required position e.g.
“M”, “1”, “2”
Speed setting Use
“1”
“2”
for light usage with liquids
for more solid consistency – for mixing
liquids and solid food contents
to stop operation
SAVE THESE INSTRUCTIONS.
“0”
“M” for ice crushing & short, powerful
impulse movements
THIS PRODUCT IS FOR HOUSEHOLD
USE ONLY!
MW_62002_Eclipse_IM.indd
3
24/06/2011 15:30:59
27 Nourse
Avenue Epping
2
Cape Town
P.O. Box 975 Eppindust 7475 South Africa
Tel: +27 21 534 8114 Fax: +27 21 534 8086
Service Centre Share Call: 086 111 5006
w e b : w w w. c r e a t i v e h o u s e w a r e s . c o . z a
MW_62002_Eclipse_IM.indd
4
24/06/2011 15:30:59
|